Aaronia SPECTRAN® V6 PLUS 500XA-6 USB Real-Time Spectrum Analyser

The Aaronia SPECTRAN® V6 PLUS 500XA-6 is a USB real-time spectrum analyser with one Rx input and one Tx output. It has an 80 MHz real-time bandwidth and is supplied with RTSA-Suite PRO PC software.

SKU: AAR 102/002

Aaronia SPECTRAN® V6 PLUS 500XA-6 USB Real-Time Spectrum Analyser

In stock

We are GST registered in New Zealand and we charge in New Zealand Dollars. Foreign-based customers please email us or call our Australian or New Zealand numbers below and we can manually process the sale without New Zealand GST. For Australian customers we can also invoice in AUD and you can pay into our Australian bank account to minimise bank fees and complexities.

 

Please note that you may be assessed for your countries duties and taxes on import as per your local regulations.

 

AUS:+61 2 913 96 981   NZ: +64 9 448 2600

Description

Designed for capturing short signal transmissions, the SPECTRAN® V6 PLUS 500XA-6 supports real-time I/Q streaming over USB 3.0. Its software supports signal identification, capture, demodulation and tracking.

The compact analyser is intended for field and laboratory measurements. Applications include spectrum monitoring, RF and microwave measurements, interference hunting, EMC testing, and Wi-Fi and wireless network measurements.

Key features

  • One Rx input and one Tx output
  • 80 MHz I/Q real-time bandwidth
  • Real-time I/Q streaming over USB
  • Dual USB 3.0 streaming connection
  • RTSA-Suite PRO spectrum analysis software
  • 16-bit ADC with dual 2 GSPS sampling
  • FFT-based POI up to 97 ns and direct I/Q-based POI up to 10 ns
  • Compact aluminium case measuring 210 x 115 x 30 mm
  • Stackable design

Applications and typical users

  • Spectrum monitoring
  • RF and microwave measurements
  • Interference hunting
  • EMC testing
  • Wi-Fi and wireless network measurements

NZ calibration and service available from Electrotest.

Frequency range 10MHz – 6GHz
Frequency range 75 MHz to 6 | 7.2 GHz
Real-time bandwidth Rx 80 MHz (opt. 120 MHz) I/Q
Real-time bandwidth Tx 120 MHz I/Q
POI Up to 97 ns (FFT-based), 10 ns (direct I/Q-based)
Max. power Rx +23 dBm
Max. power Tx +20 dBm
DANL (internal pre-amp on) Typ. -170 dBm/Hz
Amplitude accuracy (typ.) Typ. +/- 0.5 dB (compensated by FIR filter)
USB streaming connection One or two USB 3.0 (USB 3.1 Gen1; USB 3.2 Gen1)
USB bandwidth (2 x USB 3.0) Up to 784 MBytes/s sustained throughput to PC
Frequency reference accuracy 0.5 ppm (5 ppb via OCXO option)
Min.. RBW (resolution bandwidth) 5 Hz @32k FFT, 1.25 Hz @128k FFT, 157 mHz @1M FFT, 613 µHz @268M FFT
Max. RBW (resolution bandwidth) 200 MHz
Measurement units Over 20 (e.g. dBm, dBμV, V/m, A/m, W/m², dBμV/m, W/cm²)
Detector Min, Max, AVG, Peak, QPeak
Attenuator range 50 dB / 70 dB (0.5 dB steps)
Traces Over 20 (e.g. ACT, AVG, MAX, MIN, QPEAK)
Measurement modes True IQ or Power/Frequency data
Trigger Cursor, Measurement, Density
ADC Dual 2GSPS 16 Bit
DAC 2GSPS 14 Bit (16 Bit via oversampling)
GPS GPS/QZSS, GLONASS, BeiDou and Galileo (concurrent reception)
GPS synchronisation +/- 10ns timestamping in each data packet
External frequency reference input Typ. 10 MHz, max. 3.3VRMS into 50 Ohm (SMB-connector)
FPGA XC7A200T-2
DSP processing 930 GMACs
SDRAM 2 GB
Temperature range (operation) 0 °C to +50 °C (extended -40 to +75 °C)
Dimensions 210 x 115 x 30 mm
Weight 850 g
Power USB 3.2 Gen 1 Type-C PD 3.0
Power consumption Typical 15 W
Country of origin Germany
Recommended calibration interval 2 years
  • RTSA-Suite PRO PC software on USB stick
  • Power supply
  • USB cables
  • 120 MHz I/Q RTBW option
  • WiFi6E Extention 7.2 GHz
  • Ultra Low Noise Preamp
  • OCXO Timebase
  • Internal GPS
  • RF over Fiber (Rx/Tx) Set
  • Splitter/Combiner
  • 26800 mAh Power Pack
  • HyperLOG PRO Antennas
  • BicoLOG Antennas (20MHz – 3GHz)
  • IsoLOG 3D Mobile (9 kHz – 7.2 GHz)

Related Products